INCRA Miter Gauge V120

620,00Lei

Disponibilitate:
1
Cod produs:
DSFT-314545
Marca:
INCRA

Nu a fost încă evaluat
Scrie un comentariu
The extreme accuracy that made INCRA famous is now available in an extraordinary new family of incremental miter gauges. These features make the Incra miter gauges unique:
 
AngleLOCK: Precision angle indexing teeth are laser cut in solid steel to lock in many positive angle stops in 5° increments (or more dependent on type) over a full 180° range.
GlideLOCK: Four or Six (dependent on type) expansion disks adjust both sides of the bar for ZERO side play, anti-friction travel on all table saws with standard 3/4 inch x 3/8 inch or near-standard miter gauge channels, including Delta, Craftsman, imports, etc. This means that all of INCRA's incredible precision will actually show up in your work because the bar can't wiggle around in the miter slot.
 
Note: The slide guide of this stop and mitre fence fits all 3/4 inch (19 mm) T-slots as found on many machines from anglo-saxon countries and on other imported equipment. As a rule, slots on machines intended for EU countries are of a different size. Make sure before ordering that the slot is in fact 19 mm wide. If not, you cannot use these stops.
 
Don't let the small size fool you! The NEW Miter V120 puts high-resolution, repeatable accuracy within the budget of every woodworkers. An incredible 120 angle stops are laser cut into the steel protractor, with a stop available for every whole degree and two special stops at 22.5 degrees for cutting eight-sided frames and mouldings.
 
All of that precision is built into a sturdy, no-fuss package that's compact enough to fit machines where other miter gauges can be a tight squeeze, such as band saws and disc sanders. All-steel construction makes it an excellent long-term investment, and it's also upgradable as your needs change - the V120 can be equipped at any time with any IncraLOCK miter gauge fence and stop.
 
The steel miter bar is equipped with four patented GlideLOCK adjustment points for a perfect, low-friction fit in a wide variety of machines using a 3/4 inch (19 mm) miter slot. As with all INCRA crosscutting tools, a removable T-slot retaining clip is included, and the adjusters are accessible from the top for quicker set up than traditional miter bars with side-mounted adjusters.
 
Compatibility: The V120's adjustable miter bar will fit square-sided miter slots 3/4 inch (19 mm) wide, 3/8 inch (9.5 mm) deep, and either with or without a 15/16 inch (23.8 mm) wide T-slot at the bottom. The miter bar's adjustment range accommodates slot widths between 0.740 inch (18.8 mm) to 0.760 inch (19.3 mm). Diameter of halfround head: 172 mm.
 
Note: INCRA miters require a one time initial calibration before first use. Follow the instructions in the owner's manual.
 

Miter Gauge Brochure: https://incra.com/info/MiterGauge_Brochure.pdf

Incra Product Overview: https://incra.com/info/ProductOverview_2014_web.pdf

Incra Manuals: https://www.incra.com/product_manuals.html

 

Scrie un comentariu

Notă: codul HTML nu este interpretat!

Rău            Bun


Continuă

Livrare

Livrăm rapid în toată ţara prin GLS Curier la tariful unic de 19 lei (indiferent de greutate) | Sau puteți ridica personal produsele din magazinul nostru (Timișoara, str. Divizia 9 Cavalerie nr. 49). NU mai expediem cu Fan Courier datorita problemelor repetate si nerezolvate sistematic!

Contactați-ne

0745 858 618 (L-V, 10:00 - 18:00)
Orar showroom Timișoara: L-V, 10:00 - 18:00
office@finetools.ro